Stan's
Parts
|
| Item Description | Price | |
|
|
U-20 ADJUSTABLE CAMSHAFT GEAR KIT +8° to -8° in 2° increments. | $145 |
 |
U-20 SMALL JACKSHAFT GEAR This gear was made in the US by a well known timing gear manufacturer. It is made from billet alloy steel and then heat treated to increase wear life. The gear is dimensioned to provide correct jackshaft end play when installed. The price shown is for one gear although two are pictured. | $65 |
 |
A NEW SET OF 4 TIMING GEARS AND 2 NEW CHAINS FOR U20. Gears were manufactured in the Midwest by well known timing component factories. The timing gears are proper alloy steel as specified by timing gear manufacturers for timing gears and have been heat treated where appropriate per the manufacturers recommendations. Please do not hesitate to ask questions about the items up for auction. Timing components for U-20 engines are quite scarce and no timing gear/chain sets are generally offered. Ask about other available U-20 timing kits. |
$455
|
 |
A NEW COMPLETE 10 PC U-20 TIMING SET. Included are 2 new Nissan tensioners (upper and lower), 2 new Nissan timing chain guides (upper and lower), 4 new made in USA timing gears and 2 new USA made timing chains. Also included, but not shown, are all tensioner gaskets. The timing gears and chains were manufactured by a QS9000 certified timing component manufacturer in the near Chicago. The same company manufactured pistons, valves, oil pumps and various other automotive components for auto manufacturers and the aftermarket. The timing gears are proper alloy steel as specified by timing gear manufacturers for timing gears and have been heat treated, where appropriate, per the manufacturers recommendations. | $985 |
 |
R-16 ROLLER ROCKER SHAFT
ASSEMBLY This is a custom roller rocker shaft assembly that has CNC
rockers that run on a hard chromed shaft. The ratio is 1.55 according to
the designer. The assembly is designed to replace the original assembly
without modification to the cylinder head. |
$495 |
 |
R-16 REMANUFACTURED ROCKER SHAFT
ASSEMBLY. Assemblies are available for Metric and SAE assemblies. The
shaft has been hard chromed and ground back to the original diameter. The
rocker arms have bronze bushings installed and the tips have been
resurfaced. New hardware including springs, washers, plugs and pins have
been used. There is a core charge that will be refunded when a rebuildable
core has been received. |
$135 |
|
|
U-20 Upper tensioner gasket | $ 2.75 |
 |
U20 WATER PUMP - New genuine Nissan aluminum pump for 67.5 - 70 | $137 |
 |
1600 WATER PUMP - New aluminum pump for 67.5 and can be used on 64 to 67 with minor mods | $108 |
 |
1600 WATER PUMP - Remanufactured water pump for 68-70 . New pumps not available from Nissan at this time. (exchange only) | $79 |
 |
2000 UPPER RADIATOR HOSE. This is a replacement hose for 67-70 Roadsters. This hose is made in USA by a major hose and belt company. The hose is the correct length and works well. The hoses from Nissan are quite scarce and those advertised are much more expensive. | $22 |
 |
68/69 2000 LOWER RADIATOR HOSE This hose is suitable for cars with VIN numbers between SRL311-01001 and SRL311-08999. These are the cars that came with 160 MPH speedometers or the 1969 cars with the Type A steering box. The hose is an aftermarket hose made by a manufacturer with an excellent reputation. The hose is fresh and has not been resting in a warehouse for many years | $28.50 |
|
|
CAMSHAFT - Genuine Nissan NOS Roadster R16 camshaft for 67.5-70 models. This is not a forklift cam. Can also be used on 63-67 cars with metric cam gear and key and bolt. | $345 |
| SOLEX CARBURETORS - NOS pair of Mikuni 40mm carbs from Nissan. Nissan P/N 16010-H2310 | $785 | |
 |
44 MIKUNI
CARBURETOR KIT. This kit is suitably for Type 4 Mikuni carbs that include
the external float adjustment feature. These also work for 40 mm carbs
with the full cover. One kit does one carburetor. Kits are also available for the type T carburetors with the narrow float bowl cover and for the Type 2 (old style) 44mm with the two screw jet cover. It is necessary to ask about availability and pricing on these kits. |
$33 |
|
|
SOLEX AIR HORNS - Fit 44mm carburetors. 2" long chrome. Set of 4 horns. | $60 |
 |
2000 SU FOAM AIR FILTER - Replaces stock paper filter and can be cleaned and re-oiled. | $55 |
 |
FUEL FILTER BOWL - Steel replacement for damaged glass bowls used on low windshield cars. | $10 |
|
|
ROADSTER CYLINDER HEAD - New in box aluminum SAE non-smog type will fit all 1600's | $895 |
 |
OIL PUMP FOR 1600 - New pump except for used bottom cover from Roadster pump. Ready to install. Requires exchange bottom cover. | $148 |
 |
ELECTRONIC DISTRIBUTOR WITH VACUUM
ADVANCE FOR SU carburetor roadsters - All electronic with vacuum advance -
fits 1600 or 2000 with SU carburetors . Far superior to points or points
replacement distributors. Non-smog advance curve with 15 degree maximum
mechanical advance at crankshaft as in original factory setup. This
distributor has been built using an original Nissan electronic
distributor and converted to suit roadsters by using parts from an
original roadster distributor and some newly manufactured components. The original vacuum advance plate has been upgraded with a newly fabricated bearing carrier with bearings that is superior to and more durable than the original Nissan part that was prone to fail. The person in Wyoming that started making similar distributors in quantity (mass marketing) sent a sample part to me several years back. The sample was used as a guide and tooling was developed to make these parts more consistently and without much of the original labor intensive process. The person that developed this unique part said recently that he had never seen a failure of his part during the years he made and sold them. No welding is necessary with this process and there have been no pickup coil cup rivet failures found when using this bearing carrier. The functional mechanical advance components are from roadster distributors so they exactly duplicate the roadster advance curve. These components include the springs, weights and advance cam. Includes new cap and rotor and a newly made wiring harness from distributor to coil. Price is outright WITHOUT a core charge. A wiring diagram and installation instructions are included with each distributor. For general information, new Nissan distributor caps are made with aluminum terminals and provide excellent performance. It is necessary to replace the original ignition coil with one suitable for 12 volt electronic ignition. Many coil options are listed in the instructions. |
$260 |
 |
ELECTRONIC
DISTRIBUTOR FOR USE WITH SOLEX OR WEBER CARBS - All electronic, fits 1600
or 2000 with Solex or Weber type carburetors without vacuum advance. Far
superior to points or points replacement distributors. Non-smog advance
curve with 15° maximum mechanical advance at crankshaft as in original
factory setup. The hole in the housing that is made for the vacuum
advance is filled with a machined part that is threaded and retained with
a screw instead of a rubber plug. Others have been seen with a rubber
plug. Includes new cap and rotor. Includes wiring diagram. Price is
outright WITHOUT core charge. It is necessary to replace the original ignition coil with one suitable for 12 volt electronic ignition. Coil options are listed in the instructions. |
$250
|
 |
U-20 EXHAUST HEADER - Painted and includes gaskets and collector. Has 1/2" thick head flange | ASK |
 |
U-20 EXHAUST HEADER - Ceramic coated and includes gaskets and collector. Has 1/2" thick head flange. | ASK |
 |
1600 EXHAUST HEADER - Painted and includes gaskets and collector. Has 1/2" thick head flange | ASK |
 |
1600 EXHAUST HEADER - Ceramic coated and includes gaskets and collector. Has 1/2" thick head flange. | ASK |
 |
EXHAUST HEAT SHIELD TO PROTECT ENGINE MOUNT - Rare part to fit 67 2000 | $29 |
 |
FUEL PUMP DIAPHRAGM - Fits Kyosan-Denki. Some pumps are difficult | $10.50 |
Stan Chernoff (310) 320-4554 info@fairladyproducts.com